Hawaii HDOT MVSO CDL General Knowledge Practice Test 2

Test 2 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Hawaii test.

A coastal road with palm trees and green volcanic mountains, a typical landscape of Hawaii
  1. 1. What is the purpose of blocking placed against cargo on a trailer deck?

    Show answer

    Answer B: To fill the space around the cargo so it cannot slide

    Blocking is shaped to fit snugly against the cargo and fastened to the deck, removing the room the load would need in order to move.

  2. 2. Most rollovers of loaded trucks on exit and entrance ramps happen for which reason?

    Show answer

    Answer B: The ramp was taken faster than the load could tolerate

    A posted ramp speed is set for cars, and a loaded trailer with a high center of gravity can roll at a speed a car would take easily.

  3. 3. Which of these is a major cause of skids in heavy vehicles?

    Show answer

    Answer C: Over-braking, over-steering, over-acceleration or driving too fast for conditions

    Skids happen when the tires are asked for more grip than the road can give, which happens through braking, steering or accelerating too hard or simply too much speed.

  4. 4. What can repeated violations of the federal phone and texting rules cost a commercial driver?

    Show answer

    Answer D: Disqualification of the commercial driver license

    Multiple convictions for using a hand-held phone or texting while driving a commercial vehicle lead to disqualification, on top of fines for driver and carrier.

  5. 5. You must drive well below the speed of surrounding traffic, for example when climbing a steep grade with a heavy load. What should you do?

    Show answer

    Answer B: Turn on the four-way flashers to warn following traffic, where state law allows it

    Flashers warn faster traffic that a slow-moving vehicle is ahead, which helps prevent rear-end crashes; some states restrict their use while moving, so check the local rule.

  6. 6. How does bracing differ from blocking when securing cargo?

    Show answer

    Answer B: Bracing runs from the upper part of the cargo to the floor or walls to keep it from moving, while blocking fits snugly against the cargo

    Blocking is shaped to fit against the front, back or sides of a piece of cargo; bracing supports it from above so it cannot tip or shift.

  7. 7. Where must a Hawaii CDL holder go to add a motorcycle category to the commercial license?

    Show answer

    Answer D: The Commercial Driver Licensing Office

    A CDL holder may obtain a motorcycle permit at any driver licensing office, but adding the motorcycle category to the CDL itself must be done at the Commercial Driver Licensing Office.

  8. 8. Within what distance should high beams be lowered at night?

    Show answer

    Answer D: Within about 500 feet of an oncoming vehicle and within about 500 feet of a vehicle you are following

    High beams blind other drivers at close range, so they are lowered at roughly the same distance whether the other vehicle is coming toward you or is ahead of you.

  9. 9. On a scale, your loaded truck is well under the gross weight limit, but one axle is above the limit for that axle. What does this mean?

    Show answer

    Answer D: The vehicle is overloaded and the load must be shifted or reduced before you drive on

    Each axle and axle group has its own limit and each must be respected; being under the gross limit does not excuse an overloaded axle.

  10. 10. With the tractor coupled to the trailer, what should you see between the upper and lower fifth wheel plates?

    Show answer

    Answer A: No space at all between the two plates

    Any daylight between the plates means the trailer is not properly seated on the fifth wheel and the coupling can come apart under load.

  11. 11. A straight truck has a long body behind the rear axle. What happens to that overhang in a sharp left turn?

    Show answer

    Answer D: It swings out to the right and can strike a vehicle or an object on that side

    Body that hangs behind the rear axle swings the opposite way to the turn, so the tail of the truck sweeps out into the next lane or over the curb.

  12. 12. You have countersteered to correct a rear-wheel skid and the vehicle straightens out. What must you be ready for next?

    Show answer

    Answer D: The vehicle may swing back the other way, so you must steer again to correct it

    A vehicle coming out of a skid tends to overshoot and swing in the opposite direction, and the driver must be ready to countersteer a second time.

  13. 13. For an unblocked article longer than 10 feet, the minimum is two tiedowns plus how many more?

    Show answer

    Answer B: One more for every additional 10 feet of length or any part of 10 feet

    Past the first 10 feet, one more tiedown is added for each additional 10 feet of length or any fraction of that distance.

  14. 14. When a helper guides you while backing, what should be agreed on before you start?

    Show answer

    Answer D: A set of hand signals, especially the signal that means stop

    The driver and helper must agree on signals in advance, above all the stop signal, because they usually cannot hear each other.

  15. 15. Why is driving much slower than the rest of the traffic dangerous?

    Show answer

    Answer B: Other drivers must keep passing you, which creates conflicts

    Traffic that has to work its way around you produces lane changes and closing speeds, which is why a large speed difference is itself a hazard.

  16. 16. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?

    Show answer

    Answer C: Move weight off the drive axles and onto the trailer axles

    Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.

  17. 17. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?

    Show answer

    Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle

    Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.

  18. 18. How does a driver keep a vehicle with a manual transmission from rolling back when starting on an upgrade?

    Show answer

    Answer D: Partly engage the clutch before the right foot leaves the brake, or hold the vehicle with the parking brake until the engine pulls

    Something has to hold the vehicle during the instant the foot moves from the brake to the accelerator, and that is either the clutch at its engagement point or the parking brake.

  19. 19. You are drifting in the lane, yawning constantly and cannot remember the last few miles. What is the only reliable cure?

    Show answer

    Answer C: Stopping in a safe place and sleeping

    Those are classic drowsiness warning signs, and nothing except sleep repays the sleep the body is missing.

  20. 20. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?

    Show answer

    Answer B: That the seal number matches the paperwork and that the doors are properly closed

    You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.

  21. 21. Federal rules forbid operating a commercial vehicle in which condition?

    Show answer

    Answer C: In a condition likely to cause a crash or a breakdown

    A defect that makes a crash or a breakdown likely has to be corrected before the vehicle is driven, not reported at the end of the trip.

  22. 22. Why does the manual insist on a firm grip with both hands on opposite sides of the steering wheel?

    Show answer

    Answer A: A hard bump can pull the wheel out of a loose grip

    Hitting a curb or a deep pothole can jerk the wheel violently, and only a firm two-handed grip keeps the vehicle under control when that happens.

  23. 23. You are loading lengths of large diameter pipe on a flatbed. What is needed besides the tiedowns?

    Show answer

    Answer D: Chocks, wedges or cradles that keep the pipe from rolling

    Anything that can roll must be prevented from rolling by chocks, wedges, cradles or a similar device that is itself secured so it cannot come out.

  24. 24. Apart from the risk of stalling, why is rolling backwards when starting on an upgrade so serious in a heavy vehicle?

    Show answer

    Answer D: You can strike the vehicle behind you, which is often much closer than you think

    You cannot see how close the vehicle behind has stopped, and even a short roll back is enough to hit it.

  25. 25. The temperature is around freezing and the road looks wet. What is a practical way to tell whether it is icy?

    Show answer

    Answer C: Check for ice building up on the mirrors, antenna or the front of the vehicle

    Ice that forms on the mirror, antenna or windshield is a warning that the road surface is freezing too, and black ice can look like a wet road.

  26. 26. A car is following you far too closely. What is the safest response?

    Show answer

    Answer A: Open up more space ahead so you can slow gradually, avoid sudden changes, and do not speed up

    Extra room in front lets you slow smoothly instead of braking hard, which is exactly what the driver behind cannot cope with.

  27. 27. Why is a leak in the exhaust system especially dangerous in cold weather?

    Show answer

    Answer A: Carbon monoxide can build up inside a closed cab

    In winter the windows are shut and the heater is running, so exhaust gas that escapes early can reach the driver and cause drowsiness or worse.

  28. 28. How does a load carried high in the trailer affect safe speed through a curve?

    Show answer

    Answer B: It raises the rollover risk, so the speed must be lower

    A high center of gravity lets the vehicle tip long before the tires lose their grip, so height of the load directly limits curve speed.

  29. 29. Under federal rules, what is required of a commercial driver who wants to use a mobile phone while driving?

    Show answer

    Answer B: The phone must be hands-free and started with no more than a single button press, and it must not be held

    Federal rules ban texting and hand-held phone use while driving a commercial vehicle; reaching for, holding or dialing a phone is a violation.

  30. 30. Regular mirror checks during a long trip can reveal which developing problem?

    Show answer

    Answer D: Smoke coming from a tire or from a wheel

    Overheating tires, wheel bearings and brakes usually show as smoke long before anything appears on the dash, and mirrors are where a driver sees it.

  31. 31. You are told a posted bridge ahead has a weight limit lower than your gross weight. What must you do?

    Show answer

    Answer C: Take a route that avoids it, because a posted limit is a legal limit

    A posted structure limit must be obeyed exactly as any other weight limit, so a heavier vehicle has to be routed around it.

  32. 32. How long must a motor carrier keep a driver vehicle inspection report and the certification of repairs?

    Show answer

    Answer B: Three months

    The original report and the certifications attached to it are kept on file for three months from the date the report was prepared.

  33. 33. May a Hawaii CDL applicant use an out-of-state commercial learner's permit to take the tests in Hawaii?

    Show answer

    Answer D: No, an out-of-state commercial permit is not acceptable

    Hawaii does not accept an out-of-state commercial learner's permit for testing, and a driver may hold only one valid driver license at any one time.

  34. 34. You are taking a tightly curved highway exit ramp in a long combination. Where should the tractor be placed within the lane?

    Show answer

    Answer D: Toward the outside of the curve, leaving room for the trailer to track inside

    Because the trailer wheels cut to the inside of the curve, the tractor has to be kept out toward the outer edge so the trailer does not drop a wheel off the inside edge.

  35. 35. Why must the steering wheel be moved only a small amount at a time while backing?

    Show answer

    Answer B: Because a small turn of the wheel produces a large change at the rear of the vehicle

    In reverse, the effect of the steering is greatly magnified at the back of the vehicle, so a small correction is usually all that is needed.

  36. 36. What happens to braking performance if oil or grease reaches a brake lining?

    Show answer

    Answer B: That brake loses much of its effect and the vehicle can pull to one side

    A contaminated lining cannot grip the drum, so that wheel contributes little braking and the vehicle pulls toward the side that is still working.

  37. 37. Below 40 mph, what following distance does the standard commercial rule of thumb call for?

    Show answer

    Answer C: One second for every 10 feet of vehicle length

    The base rule allows one second of space for each 10 feet of vehicle length while speed stays under 40 mph.

  38. 38. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?

    Show answer

    Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear

    On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.

  39. 39. How do you avoid the sharp lurch that comes at the very end of a stop in a heavy vehicle?

    Show answer

    Answer A: Ease off the brake pressure just before the vehicle actually comes to rest

    A smooth stop is finished by reducing pedal pressure as the vehicle settles, so the suspension does not rock the cab and the load forward.

  40. 40. You stop to check the load. Which set of things are you looking at?

    Show answer

    Answer C: Tight tiedowns, cargo that has not moved, secure doors and tarps still fastened

    A cargo check covers the load and everything holding it: whether it has shifted, whether the devices are still tight, and whether doors and covers are still closed and fastened.

  41. 41. What are you checking when you pull the engine oil dipstick during the pre-trip?

    Show answer

    Answer A: That the oil level is within the safe operating range marked on the stick

    The dipstick shows whether there is enough oil to lubricate and cool the engine, and a level outside the safe range must be corrected before driving.

  42. 42. Why does a load of live animals need special attention?

    Show answer

    Answer D: The animals move and lean, so the center of gravity shifts and the vehicle can be pushed off balance in a turn

    A live load will not stay where it is put, and that movement changes the balance of the vehicle exactly when a curve is loading it most.

  43. 43. Total stopping distance is made up of which parts?

    Show answer

    Answer A: Perception distance, reaction distance and braking distance

    The vehicle travels while the hazard is recognized, while the driver moves to the pedal, and again while the brakes slow the vehicle.

  44. 44. How does the working load limit of a tiedown relate to the force that would break it?

    Show answer

    Answer B: The working load limit is a fraction of the breaking strength and is the figure you use

    The working load limit is set well below the point at which the device would fail, and securement is always calculated from the working load limit, never from breaking strength.

  45. 45. What does the commercial driver manual tell you to do with the parking brake when you leave your vehicle?

    Show answer

    Answer B: Apply the parking brake every time you leave the vehicle

    The manual is explicit that the parking brake goes on whenever the driver leaves the vehicle, because once nobody is at the controls it is the only thing holding it.

  46. 46. How are the headlights, marker lights and turn signals checked during the seven-step inspection?

    Show answer

    Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle

    The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.

  47. 47. After the first inspection of a trip, how often must cargo securement be checked again?

    Show answer

    Answer D: Every 3 hours or 150 miles or at each change of duty status, whichever happens first

    The load must be re-checked at whichever of those points arrives first, so a loosening tiedown is found long before it fails.

  48. 48. A driver hauling a sealed trailer that cannot be opened is still responsible for what?

    Show answer

    Answer D: Making sure the rig is not over the gross or axle weight limits

    A seal prevents inspecting the contents, but the driver must still confirm the vehicle is not overloaded.

  49. 49. What should be checked about the power steering system in the engine compartment?

    Show answer

    Answer D: That the fluid level is correct and the hoses and pump are not leaking

    Losing power steering fluid means losing steering assistance, which can happen suddenly and makes a heavy vehicle very hard to turn.

  50. 50. You need to check your route on a navigation device. What is the correct approach?

    Show answer

    Answer D: Set it before the trip or after you have parked

    Route programming is planning work, and it belongs to the time before the wheels turn or after the vehicle is safely parked off the roadway.